GReddy Turbo Kit Honda Civic Si EP3 (K20A) T517Z 8cm2
3-3 Oil Pressure Line Installation Install the 3-way fitting to the block first. 3-way fitting PF PT PT PT Oil Pressure Switch (1) Remov
(2) Install the exhaust manifold using the factory gasket. * Use a new exhaust manifold gasket. * Use factory nuts on the top side of the fla
3-7 Oil Return Installation (1) Install the provided oil return pipe to the turbocharger using the provided gasket and hardware as shown. (Parts
• Reinstall the heat shield and make sure there are enough clearance between the hose and the shield and the drive shaft. * Oil return hose to h
(4) Cut the master power vacuum hose by the intake manifold and install the 3-way fitting. Connect the 5∅ side to the actuator with the provided 5∅ h
(6) Install stud bolts on to the inlet of the turbo, and install suction adapter using provided gasket and restrictor. (Parts used #5,9,41,62)
(2) Check the fitment of the downpipe heat shield and install gasket on the catalytic converter end of the downpipe. * The heat shield
3-12 Fuel Injectors Installation (1) Disconnect the fuel injector connectors and ground wire on the fuel delivery tube and remove the fuel del
3-13 e-Manage Installation (1) Remove the cover under the glove box to access the ECU and ECU harness. (2) Install the Grey wire to the e-Manage I
86 4 2 73 7 910 13 115 6 184 23 222 225 6 29311 2 3 4 5 68 10 4113 15168 117 2221 23 241 2 3 4 5 6 7 9 11 110 2 16 1529 118 20 1 23 223 4
Honda Civic Si EP3 (K20A) T517Z 8cm2 Installation Manual Please read the entire manual before installing this kit. Application: Make
e-manage Factory ECU Pin # Wire Color Description ECU Pin # Color Code3 White MAP IN A19 arness) Green/Red MAP (h4 Grey Throttle A15 Red/Black TP
3-15 Starting the Engine (1) Refill the engine oil to factory spec. (2) Check all the hoses and wires ne then nect egative e of the battery. (
e-manage Information Important! The e-manage included in this kit is preprogrammed for the this turbo kit. Do not attempt to adjust any of the se
Checking Error Code Chart CODEIncorrect wiring or disconnected Airflow Signal 1input error1115Airflow Signal 1 No InjecAirflow v
1. Parts List 1. Turbocharger T517Z 8cm2 P565 1 2. Turbo Exhaust Manifold (Cast Iron) 1 3, Down Pipe
1. Parts List 27. Vacuum Hose (Blue) 5∅ x 200mm (for Actuator) 1 28. Rubber Hose 8Ø X 500mm (for Idle controller)
1. Parts List 56. M6 X 10 P=1.0 B S/W F/W - (Down pipe heat shield) 2 57. M6 X 15 P=1.0 B S/W F/W - (Suction pipe & compre
1. Parts List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1. Parts List 26 27~30 31 32~33 34~39 40 41 42 43 44 45 46 47 48 49~50 51 52 53 54 55 56~66
2. Removal of Stock Parts When removing the stock parts, make sure you read over the factory repair manual for proper procedures. 2-1 Disconnect
3. Kit Installation 3-1 Factory heat shield modification (1) Heat shield plate modification Trim the shaded area on the heat shield plate that was
Commentaires sur ces manuels