TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 T518Z 10㎝2 (Internal Wastegate) !Vehicle Type Chassis Code Engine Code Transm
―8― 3-3 Installation of Oil Pan Install oil pan。 ※ Use liquid gasket. 3-4 Insulation of Electrical Harness (1) Cut out the portion of th
―9― 3-5 Turbo Manifold Installation (1) Wrap the lower radiator hose with thermo wrap as shown in the diagram. 〈Parts №43〉 (2) Inst
―10― (3) Install the Turbo Mounting Bracket A. Using the Turbo Bracket to Pulley Spacers A & B, 。 ※ Turbo Bracket to Pulley Spacers A has a
―11― 〈Parts №14,15〉 (2) Install the factory oil switch onto the 3 way fitting as shown in the diagram. ※ Be sure to use thread seal. (3)
―12― (6) Install the Oil Pressure Line between the Banjo Fitting and 90 degree elbow. Mount the Oil Pressure Line to the Radiato
―13― (2) Wrap the Air/Fuel Sensor Harness with thermo cloth. 〈Parts №43〉 (3) Install the O2 and Air Fuel Sensor onto the Test
―14― (6) Readjust exhaust piping from the Turbine as needed, then tighten. (7) Reconnect O2 Sensor and Air Fuel Sensor harness cou
―15― (2) Install Compression Pipes C11 to C-3. ※ Temporarily Finger Tighten. 〈Parts №5,6,7,25,27,32,34〉 ※ When installing C-2(№6)pleas
―16― (3) Remove the front bumper bracket and drill out two holes as shown in the diagram. (4) Reinstall the front bumper bracket, t
―17― (2) Install the Airflow Meter。 〈Parts №55〉 (3) Wrap the Airflow Meter Harness with thermo wrap. Then connect the Airflow Meter Coupler
―18― (3) Install the filter, external cage and tighten the Airinx Top Bolt。 (4) Install the Intake Pipe and Airinx. <Parts №9,29,33,3
―19― 3-16 OEM Bumper Installation (1) Modify the OEM bumper reinforcement by cutting and removing material as shown in the diagram. Make
―20― 4.Power Graph ○ This Turbo Kit is designed to boost up to 6 to 7.5 PSI. ※ Important This Turbo Kit is not Pre-tuned. The customer or
―1― 1.Parts List 1.Turbo Charger T518Z 10C㎡ P555 1 2.Exhaust Manifold (SUS 42.7φ-50.8φ) 1 3.Down Pipe (50φ-60φ) 1 4.Test Pipe 1 5.Comp
―2― 35.Gasket Turbine IN 1 36. 〃 Turbine OUT 1 37. 〃 Intake Tube Adapter Flange 1 38. 〃 Small Oil Return 1 39. 〃 Cylinder Head to T
―3― Parts List Diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22~24 25~27 28,29 30~34
―4― 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58~67 68
―5― 2.Removing OEM Parts Refer to the factory service manual prior to the uninstallation of OEM parts. 2-1 Disconnect the negative batter
―6― 3.Turbo Kit Mounting 3-1 Oil return tube positioning (1) Tap a 13mm hole into the oil pan location shown in the diagram (2) Install th
―7― (5) Temporarily install the turbo and gaskets using the OEM bolts. 〈Part # 35,64,65〉 (6) Install the oil return hose bracket usi
Commentaires sur ces manuels